Frequently Asked Questions
How to pair your WiTi Wireless Towing Interface
Do you need help to pair your WiTi Wireless Towing Interface? Follow these easy steps to pair your devices.
Use the signal LEDs to see pairing status. The amber LED should be lit indicating there is power to the device.
Step 1
Hold pair while pressing and releasing the reset button on the Anti-Theft System. The red LED will rapidly indicating the unit is in pairing mode
Step 2
Hold pair while pressing and releasing the reset button on the Wireless Towing Interface.
When successfully paired, both units will flash slowly for a few seconds.
How to program your WiTi remote controls
Need help to program your WiTi Remotes? Follow these easy steps to pair your devices.
Step 1
Press the RF button on the Anti-Theft System. A blue LED will flash once to indicate it is in programming mode.
Step 2
Press the A button on the remote to program the alarm activation button. The blue LED will flash multiple times to indicate pairing was successful.
Step 3
Enter programming mode by pressing the RF button. Then press the B button to program the panic button. The blue LED will flash multiple times to indicate pairing was successful.
Repeat this process with any additional remotes.
How to pair your WiTi Wireless Electric Brake Controller
Need help to pair your WiTi Wireless Electric Brake Controller with your system? Follow these easy steps to pair your devices.
Use the signal LEDs to see pairing status. The amber LED should be lit indicating there is power to the device.
Step 1
Hold pair while pressing and releasing the reset button on the Anti-Theft System. The red LED will flash rapidly indicating the unit is in pairing mode.
Step 2
Press the override button on the Wireless Brake Controller while pushing it into the 12V socket.
When successful the message "pairing successful" will appear briefly and the linked icon will display on the screen.
How to program WiTi Intrusion Detection sensors
Need help to program your WiTi Intrusion Detection? Follow these easy steps to pair your devices.
Step 1 - Motion sensor
Press the RF button on the Anti-Theft System and the blue LED above it will flash once to indicate programming mode is active.
Step 2
Flick the power switch on. This will pair the sensor. The blue LED will flash multiple times to indicate paring was successful.
Step 3 - Door sensor
Press the RF button on the Anti-Theft System and the blue LED will flash once to indicate programming mode is active.
Step 4
Open the door to activate the sensor and the blue LED will flash to indicate pairing was successful.
WiTi Intrusion detection system will now be connected and ready to arm.
Sensitivity of the WiTi Anti Theft alarm
WiTi incorporates the very latest gyroscope and accelerometer technology, similar to that found in drones. This enables us to program WiTi to detect different movements and triggers.
Acceleration - WiTi is very sensitive to acceleration. Forward or reverse acceleration will trigger WiTi Anti-Theft.
Rocking the van side to side - this motion has been programmed out so that the alarm does not trigger in windy conditions.
Will windy conditions set off the Anti Theft alarm
Wind or gentle movement will not activate the alarm. WiTi is sensitive to two types of movement, sharp knocks and forward or backward acceleration. In practice you can walk around inside your caravan without the alarm being triggered but if you were to slam a door or bang on the side of the caravan or trailer this sharp knock would trigger the alarm.
Moving the caravan forwards or backwards, as in an attempt to steal the caravan, will also trigger the Anti Theft system.
What if someone else needs to tow my van?
If your caravan / trailer needs to be towed by another vehicle then the anti-theft system will need to be deactivated by pressing the button on the remote control. An option is to leave the existing wiring harness in place and add the Wireless Interface in parallel then both the fixed wiring harness and the Wireless Interface can be used depending on the tow vehicle.
How much current does WiTi use
In standby mode and with the alarm and anti-theft system activated, WiTi will draw 0.08A. On a 100 A/Hr battery WiTi will be operate for approximately 1 month without the battery receiving any charge. In normal conditions and whilst travelling WiTi will draw very little additional current over existing lighting and braking requirements.
A solar panel connected to the house battery will provide more than enough power to maintain charge on the battery and operate WiTi whilst travelling.